Expert Answers about Chevrolet RV and Camper Hitch

• Do You Carry a Swagan Clamp-On or Bolt-On RV/Camper Bumper Hitch
• Yes, the RV Clamp-On Bumper Hitch is available by itself. It is part # S64025 and I have added a link to it below. Remember, your bumper needs to be a 4x4 inch continuous-weld steel bumper. It cannot be used on spot welded or aluminum camper bumpers.
  view full answer...


• Availability of RV Bumper Trailer Hitch Receiver and Bike Rack
• Any of our RV and motor home bike racks, see link, with a 2 inch shank will work with the RV Bumper 2 inch Trailer Hitch Receiver with Anti-Rattle - Clamp-On, part # S64025. Please be aware that the springs on a camper are very different than those on a vehicle, and the bikes will be jarred quite a bit. No matter which bike rack you choose, you will need to be sure to secure the bikes with bungees to prevent damage to the bikes, rack, or your camper.
  view full answer...


• Can 70 lb Recumbent Bike Be Towed with Hitch Bike Rack Behind 5th Wheel Camper
• Hitches like the Curt Adjustable RV Hitch # 13703 that you were looking at are designed to attach to either I-beam, C-channel or box RV frames, so bolting them to any other structure is not recommended for safety reasons. The # 13703, fits frames that are between 22 and 72 inches wide outside to outside. There are also hitches that attach to your 5th Wheel bumper instead. For example, the Curt # E-100, fits a 4 inch square tube bumper and offers a 350 lb tongue weight capacity. That being...
  view full answer...


• Trailer Hitch Option for 2022 Coleman 202RD Travel Trailer w/ Stabilizer Jacks Interfering w/ Hitch
• If your 2022 Coleman 202RD travel trailer has stabilizer jacks interfering with where a hitch like the Adjustable Width Trailer Hitch Receiver for RVs # 13703 would install, we do have an alternate style like the Curt RV Bumper 2" Trailer Hitch Receiver # E-100. The Curt RV Bumper 2" Trailer Hitch Receiver # E-100 fits 4" square channel bumpers on the rear of many RVs and towable campers.
  view full answer...


• Motorhome Bike Rack Availability
• We do offer a range of bike carriers that are suitable for use on the back of a trailer and all can be seen on the provided link. We offer RV-approved racks for camper roof or hitch mounting, and also for attachment to a ladder, ball mount or to the bumper on a camper. None of these racks is designed to attach to a spare tire carrier however. The linked article will explain further. At the back of an RV or trailer the ride quality is much rougher than that of a passenger vehicle, it takes...
  view full answer...


• Availability Of Hitch Bike Rack To Fit On the Rear Of a Travel Trailer
• When using a 2-inch hitch adapter that clamps to your 4-inch square RV bumper on a travel trailer you will not want to exceed the limits of your bumper. The bumper towing and tongue capacities may be indicated on the bumper itself, but if not you could check your trailers owner manual or contact the manufacturer of your travel trailer. Also remember when using a bolt-on adapter your bumper needs to be a 4x4 inch continuous-weld steel bumper. It cannot be used on spot welded or aluminum...
  view full answer...


• Adjustable Width Frame-Mounted Trailer Hitch Receiver for RVs 13703
• We do not have the ability to modify any of the RV hitches like Curt # 13703 that we sell and that includes something like addition of a second receiver opening to allow use of a hitch motorcycle carrier that requires dual receivers. At one time we used to offer a swivel-type wheeled motorcycle carrier that required multiple receivers in order to support the substantial combined weight of the carrier itself plus the loaded motorcycle. I recommend you contact Coachmen RV with your 5th wheel's...
  view full answer...


• Trailer Hitch Recommendation for Rear of 2006 Keystone Raptor 3712TS
• Our most universal fitting RV hitch is the Curt multi-fit hitch part # 13703 which can fit basically all frame styles between 22 and 72 inches apart. I attached an install video for this hitch for you to check out as well.
  view full answer...


• RV Camper Key Replacement for Pop Up with Lost Key
• Most likely the # A524VP is what you'd need as this is the very common RV key CH751 that people actually complain about opening basically all RV doors. Since you have an older popup the likelihood of this being the right key is very high although we can't totally verify that.
  view full answer...


• Recessed and Lockable Gravity Water Fill Ports For a Camper
• We actually have a selection of recessed gravity fill ports that you can use on your camper that are lockable. I will list them for you below. Slide-Out RV Gravity Fill Inlet with Lockable Latch - Polar White # 37237525 Valterra Lockable RV Gravity Fill Water Inlet - White # A01-2002VP Valterra Lockable RV Gravity Fill Water Inlet - Black # A01-2002BKVP Valterra Lockable Dual RV Water Inlets - City Water and Gravity Fill - Plastic Valve - White # A01-2004VP Valterra Lockable Dual RV Water...
  view full answer...


• RV Dump Tank Adapter to Go From Permanent Attachment Fitting to Bayonet Fitting
• If you are sure you have a permanent style of drain valve on your camper the correct adapter is the part # CAM39422 that you referenced. This would attach to your current setup and give you a bayonet style of attachment for connecting to RV dump sites.
  view full answer...


• Storage Lot RV Cover for Travel Trailer
• I think the smallest we will have is still going to be too large for little egg type camper. Awesome camper by the way, see very few of these anymore. The Adco Polypropylene Storage Lot RV Cover for Travel Trailer, # 290-74838 is for trailers from 12-15 feet. My suggestion, if this is something you plan to keep for an extended length of time, locate a local custom boat cover maker. Have them sew up a custom fir for you. This will be more expensive but well worth the cost if you will...
  view full answer...


• What Entry Door Holders do You Recommend for My Fleetwood Pop-Up Camper?
• We definitely have what you are looking for. We do have some different options as far as size. Here are the different thicknesses we offer: - Fold Down Door Holders for RV Entry Door # 37211815 (1/16 inch thick) - Fold Down Door Holders for RV Entry Door # 37211835 (1/2 inch thick) - Fold Down Door Holders for RV Entry Door # 37211825 (1/4 inch thick) I went ahead and linked description videos that go through these different parts. If you had a different door in mind (apart from the...
  view full answer...


• Solution for Bike Rack on Vintage Camper 62 Shasta Airflyte
• The Curt RV Bumper Hitch - 2", # C19101 you referenced is designed for 4" x 2" RV bumpers. Without changing the current steel bumper, providing it and the mounts are solid enough, you may be able to source a a steel plate to use as a spacer and mount this item securely to your 1-1/2" by 3" bumper. If you have the space on the A-frame of your trailer, I suggest the Stromberg Carlson Bike Bunk Trailer-Mounted Bike Rack Carrier for A-Frame Trailers, # CC-275. Please note the attached product...
  view full answer...


• Wi-Fi and Hotspot Kit for Lippert OneControl Hotspot Prepped RV Campers
• You will need the Wi-Fi and Hotspot Kit # LC35UD for your RV Camper that came prepped with the Lippert OneControl Hotspot system. The kit includes the internal and external antenna you need. You will also need to contact or visit an AT&T store in your area to get a sim card and activate a LCI service plan. I have linked the installation instruction for this kit below that will help you understand the installation and required service plan.
  view full answer...


• How to Power a Furrion Monitor in an RV That Does Not Have a 12v Outlet
• I do have a solution for you, but the only power cord available for the Replacement 7" Monitor for Furrion Vision S Wireless RV Camera System # FR47FR is the Replacement Furrion Monitor Power Cable # C-FOS07TAPK-006. There is not a USB option available. That being said, you can add a 12v outlet to your RV using the 12 Volt Outlet Kit # RM-9332 which would provide you with the 12v outlet needed to power the monitor with the current power cord.
  view full answer...


• Availability of Scissor Steps That Mount Underneath the Camper
• The mounting bracket on the Brophy Aluminum Scissor Steps, part # AS24, is 25 inches long and 1-1/2 inches wide and should be placed 1/8 inch below the lowest part of the door on your RV for installation. The steps I have that are made to bolt or weld onto the trailer frame are the Stromberg Carlson brand. They will only have single, double, and triple steps. I am including a link to a product page that will list all of the Stromberg Carlson steps I have available. I also have the Outriggers...
  view full answer...


• Availability of Propane Extension Hose for Portable RV Dual Fuel Inverter Generator
• The Firman 3,300-Watt Portable RV Dual Fuel Inverter Generator, # FIR54FR includes a propane hose with regulator; you will need to use the included hose with regulator as it is specifically designed for this generator and has a built in solenoid. Our contact on the Tech side at Firman stated that any consideration of altering the operation should be discussed through their tech line.
  view full answer...


• Recommended Trailer Hitch for 2016 Rockwood 8280WS Fifth Wheel
• We do offer universal-fit trailer hitches for use on trailers and motorhomes. These come in two basic types, bumper-mount and frame mount. The linked page will show you all options such as Curt's bumper-mount # E-100 that is intended for use on 4-inch square channel bumpers as well as frame-mount hitch # 13703. I could not find the bumper specs for your Rockwood 5th wheel but your dealer or owner's manual can confirm which you have and help you decide between the two hitch types. Please...
  view full answer...


• Availability of Exterior Rear Ladder To Fit 1998 Pastime 700 FDS Camper
• I have available three choices for an RV exterior roof ladder. The Stromberg Carlson RV Exterior Ladder, part # LA-401, is a universal ladder that will fit RVs with either a contoured or a straight rear wall. It is 99-1/2 inches tall, can be customized for anything shorter than 99-1/2 inches. It is 13 inches wide and the distance between the rungs is 12 inches. The stand-offs can be positioned anywhere along the ladder for additional strength. The other two choices are made by Surco and...
  view full answer...